public:wireless_lan_using_linux
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
public:wireless_lan_using_linux [2006/12/15 10:23] – kohofer | public:wireless_lan_using_linux [2013/05/06 14:50] – [Setup of the UNIBZ Wireless LAN for Linux WPA] KoHofer@unibz.it | ||
---|---|---|---|
Line 3: | Line 3: | ||
====== Setup of the UNIBZ Wireless LAN for Linux WPA ====== | ====== Setup of the UNIBZ Wireless LAN for Linux WPA ====== | ||
- | Security used within the WLAN Network: WPA1/WPA2 + PEAP + MSCHAPv2 | + | Security used within the WLAN Network: WPA/WPA2 + PEAP + MSCHAPv2 |
- | ===== Pre-requisites ===== | + | * Wireless Network SSID: **ScientificNetworkSouthTyrol** |
+ | * Security: **WPA/WPA 2 Enterprise** | ||
+ | * Authentication: | ||
+ | * Inner Authentication: | ||
+ | * Certificate: | ||
+ | * Username: **< | ||
+ | * Password: **< | ||
+ | * IP Address: **Automatic (DHCP)** | ||
+ | |||
+ | ===== | ||
+ | Pre-requisites ===== | ||
* Drivers for your Wireless Adapter and Requirements, | * Drivers for your Wireless Adapter and Requirements, | ||
Line 20: | Line 30: | ||
Other Wireless LAN resources for Linux can be found here [[http:// | Other Wireless LAN resources for Linux can be found here [[http:// | ||
+ | |||
+ | ===== (K)(X)Ubuntu 9.10 Using NetworkManager ===== | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | Links: | ||
+ | |||
+ | [[https:// | ||
+ | |||
+ | ====== (K)(X)Ubuntu < 9.10 Manually ====== | ||
===== Installing wpa_supplicant ===== | ===== Installing wpa_supplicant ===== | ||
Line 26: | Line 48: | ||
2. Configure / | 2. Configure / | ||
+ | |||
+ | Download {{public: | ||
less / | less / | ||
Line 65: | Line 89: | ||
+ | ====== Configuration for Wired Authentication 802.1x (Cable) ====== | ||
- | ===== Using NetworkManager ===== | + | This is the same Authentication Method as Wireless, but here we\\ |
+ | use an Ethernet cable. | ||
- | [[https:// | + | ===== Using Network Manager ===== |
- | ====== Configuration for wired authentication 802.1x ====== | + | Try this first if you are using a Ubuntu |
- | | + | Network Manager has the ability to be configured for 802.1x Authentication. |
+ | |||
+ | Basic steps: | ||
+ | |||
+ | * Click on the Network Symbol (2 Arrows) in the upper right task-bar (either with left/right mouse click) | ||
+ | * Edit Connections... in Network Manager | ||
+ | * In the first Tab: Wired press Add Button | ||
+ | * Fill out Connection name: < | ||
+ | * Go to 2nd tab 802.1X Security, tick: Use 802.1X security for this connection | ||
+ | * Authentication: | ||
+ | * CA certificate: | ||
+ | * PEAP version: Automatic | ||
+ | * Inner authentication: | ||
+ | * Username: < | ||
+ | * Password: < | ||
+ | * Save... | ||
+ | * Click again on the Network Symbol and select the newly create Connection | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | |||
+ | ===== Manual Configuration ===== | ||
+ | |||
+ | For the more " | ||
+ | |||
+ | |||
+ | Make sure you have installed | ||
+ | |||
+ | sudo apt-get install wpa_supplicant wpa_gui | ||
+ | |||
+ | Edit the configuration file: / | ||
+ | |||
+ | vi / | ||
< | < | ||
Line 92: | Line 153: | ||
</ | </ | ||
+ | Now execute the following commands: | ||
+ | |||
+ | Starts wpa_supplicant with wired driver (-D wired) and in daemon mode (-B) | ||
+ | * sudo wpa_supplicant -D wired -c / | ||
+ | |||
+ | Start wpa_gui to enter username and password | ||
+ | * sudo wpa_gui | ||
+ | * Login with username@unibz.it and password | ||
+ | Get an IP Address | ||
+ | * sudo dhclient3 eth0 | ||
+ | |||
+ | --- // |
/data/www/wiki.inf.unibz.it/data/pages/public/wireless_lan_using_linux.txt · Last modified: 2019/01/16 10:03 by 127.0.0.1