tech:documentation:procedures:vm:vm_disk_expansion_lvm_xfs
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
tech:documentation:procedures:vm:vm_disk_expansion_lvm_xfs [2009/02/05 15:12] – ccumer | tech:documentation:procedures:vm:vm_disk_expansion_lvm_xfs [2014/03/14 14:25] – [FOR EXT3/4] kohofer | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ======VM disk Expansion LVM+XFS======= | + | ====== VM disk Expansion LVM with XFS/EXT4 ======= |
- | Expand the original disk or add a second vdisk from Infrastructure client.\\ If you want to perform a grow w/o reboot you have to add a second disk | + | <note important> |
- | **THEN TAKE A SNAPSHOT!!!** | + | |
- | then from on the vm either create an additional partirion on the free space. The partition type us 8e | + | Expand the original disk or add a second vdisk from **Infrastructure Client**.\\ |
- | <code> | + | <del>If you want to perform a grow w/o reboot you have to add a second disk.</del> |
- | cfdisk | + | |
- | ### for example if the new partition is /dev/sda3 | + | |
- | pvcreate /dev/sda3 | + | |
- | </code> | + | |
- | or assign the whole new disk to lvm | + | If you are on a kernel newer or equal to 2.6.32 then you can issue the command |
- | < | + | |
- | cfdisk /dev/sdb | + | |
- | ### for example if the new partition is /dev/sda3 | + | |
- | pvcreate /dev/sdb | + | |
- | </ | + | |
- | now you have to extend the volgroup. use '' | + | < |
- | < | + | |
- | vdisplay | + | to get the new size w/o reboot. |
+ | |||
+ | |||
+ | In case you cant see the " | ||
+ | |||
+ | echo "- - -" > / | ||
+ | |||
+ | Do this for all host0,1,2 etc. | ||
+ | |||
+ | |||
+ | or | ||
+ | |||
+ | echo " | ||
+ | |||
+ | whereby after scsi_device you need to find the correct scsi device | ||
+ | |||
+ | |||
+ | |||
+ | **EXPAND ORIGINAL DISK** | ||
+ | |||
+ | Create an additional partition on the free space, say you increased the existing disc | ||
+ | from 8GB to 15GB. The partition type is 8e. | ||
+ | |||
+ | cfdisk /dev/sda | ||
+ | |||
+ | # for example if the new partition is /dev/sda3 | ||
+ | |||
+ | # create logical disk /dev/sda3 of type 8e (Linux LVM) | ||
+ | |||
+ | # make disk visible to linux | ||
+ | |||
+ | partprobe | ||
+ | pvcreate /dev/sda3 | ||
+ | |||
+ | now you have to extend the volgroup. use '' | ||
+ | in this example it' | ||
+ | |||
+ | | ||
--- Logical volume --- | --- Logical volume --- | ||
LV Name / | LV Name / | ||
Line 78: | Line 105: | ||
- | </ | + | and we assume the new partition is /dev/sda3 |
- | < | + | |
- | vgextend base /dev/sda3 | + | |
- | </ | + | |
check with '' | check with '' | ||
- | Now we extend the " | + | pvscan |
- | < | + | Now we extend the " |
- | lvextend | + | 11.5 G is the NEW total size of the disk we want to extend! |
- | </code> | + | |
+ | Extend the LV to use all free space | ||
+ | lvextend -l +100%FREE | ||
+ | |||
+ | Extend with 20G | ||
+ | lvextend -L +20G | ||
now we have to grow the filesystem /data | now we have to grow the filesystem /data | ||
- | < | + | |
- | xfs_growfs /data | + | |
- | </code> | + | |
+ | |||
+ | ===== FOR EXT3/4 ===== | ||
+ | |||
+ | Extend filesystem | ||
+ | |||
+ | vgextend base /dev/sda3 | ||
+ | |||
+ | lvextend -l +100%FREE / | ||
+ | |||
+ | Check that the filesystem is ok, **but only if the FS is unmounted** | ||
+ | |||
+ | fsck.ext4 -f /dev/base | ||
+ | |||
+ | Now resize the filesystem | ||
+ | |||
+ | resize2fs -p / | ||
+ | resize2fs -p / | ||
+ | |||
+ | |||
+ | ===== For swap ===== | ||
+ | |||
+ | swapoff / | ||
+ | lvextend -L 3.9G / | ||
+ | mkswap / | ||
+ | swapon / | ||
+ | free | ||
+ | |||
+ | Check if filesystems are ok, and only then release the snapshot | ||
+ | |||
+ | |||
+ | ======= Create LVM ======= | ||
+ | |||
+ | Find all LVM VG | ||
+ | |||
+ | vgscan | ||
+ | |||
+ | Create Physical Volumes | ||
+ | |||
+ | Der Befehl pvcreate legt den VGDA Block auf dem PV an. Er muss für jedes PV ausgeführt werden, bevor es von LVM verwendet werden kann: | ||
+ | |||
+ | | ||
+ | |||
+ | Volume Groups anlegen | ||
+ | |||
+ | Jetzt legen wir mit ' | ||
+ | |||
+ | | ||
+ | |||
+ | Logische Volumes anlegen. | ||
+ | |||
+ | Hier legen wir jetzt alle unsere logischen Volumes an. Als Namen verwenden wir, etwas fantasielos, | ||
+ | |||
+ | | ||
+ | |||
+ | oder wir könne die Größen angeben! (1500M) | ||
+ | |||
+ | | ||
+ | |||
+ | Filesysteme anlegen | ||
+ | |||
+ | Ab jetzt können die logischen Partitionen, | ||
+ | |||
+ | mkfs.ext4 / | ||
+ | |||
+ | fstab anpassen | ||
+ | |||
+ | Damit die neuen Filesysteme nun bei jedem Systemstart automatisch gemountet werden, müssen wir sie in die Datei /etc/fstab eintragen (siehe 'man fstab' | ||
+ | |||
+ | / | ||
+ | |||
+ | http:// | ||
+ | |||
+ | http:// |
/data/www/wiki.inf.unibz.it/data/pages/tech/documentation/procedures/vm/vm_disk_expansion_lvm_xfs.txt · Last modified: 2020/10/13 16:46 by kohofer