Differences

This shows you the differences between two versions of the page.

--- auth:howto:linux:vpnclient [2020/04/21 11:52] – [Instructions for Linux using Openconnect Client (recommended)] kohofer
+++ auth:howto:linux:vpnclient [2020/10/30 13:20] – [Instructions for Linux vpnc Client] kohofer
@@ Line 69: / Line 69: @@
 ===== Instructions for Linux using openconnect Client (recommended) =====
-===== Installation =====
 Run this command to install openconnect client and OpenConnect plugin GNOME GUI
@@ Line 78: / Line 76: @@
 Once installed open Settings and go to Network, press + right of the VPN section.
-Select **Cisco AnyConnect Compatible VPN (openconnect)** and enter the details:
+{{:auth:howto:linux:network_vpn.png?400|}}
+Select **Cisco AnyConnect Compatible VPN (openconnect)** and fill out as shown below:
+{{:auth:howto:linux:add_vpn_openconnect.png?400|}}
+{{:auth:howto:linux:details_vpn.png?300|Details}} {{:auth:howto:linux:identity_vpn.png?300|Identity}}
+{{:auth:howto:linux:ipv4_vpn.png?300|IPv4}} {{:auth:howto:linux:ipv6_vpn.png?300|IPv6}}
 **Details**
@@ Line 87: / Line 93: @@
   - VPN Protocol: Cisco AnyConnect
   - Gateway: vpn.scientificnet.org
-  - CA Certificate: download from here, not really necessary!
+  - CA Certificate: download from {{ :auth:howto:linux:vpn-scientificnet-org.pem |here}}, not really necessary!
 The rest can be left as it is.
@@ Line 96: / Line 102: @@
   - Routes: ON
+Press <color #22b14c>Apply</color>
+Now you can enable the VPN connection!
+Move the slider from OFF to ON, a small window should open,
+{{:auth:howto:linux:enable_vpn.png?400|Enable VPN}}
+make sure that for VPN Host you select: **vpn.scientificnet.org**
+Enter your unibz Username, without @unibz.it and your unibz Password.
+{{:auth:howto:linux:connect_vpn.png?400|Connect VPN}}
+Press **Login**
+If all goes well the slider should remain in ON position, if not check the Log.
+To verify launch this command in a terminal:
+  ifconfig
+You should get a new interface --> vpn0: with an IP Address: 172.xxx.xxx.xxx
 ===== Instructions for Linux vpnc Client =====
@@ Line 127: / Line 152: @@
 IPSec gateway vpn.unibz.it
 IPSec ID Unibz
-IPSec obfuscated secret 06294C134E0BEBDA4B449B56BFD305D35D12DABF4044EDB6794926C2CA6D5AEDFE6342DF190E566EB11215DDC1591D5CB6ABEBEB593693C6D0B2077D78034B6AFEEA3221E77F4
+IPSec obfuscated secret 06294C134E0BEBDA4B449B56BFD305D35D12DABF4044EDB6794926C2CA6D5AEDFE6342DF190E566EB11215DDC1591D5CB6ABEBEB593693C6D0B2077D78034B6AFEEA3221E77F4C9858DD711AA8DE58F6
-C9858DD711AA8DE58F6
 Xauth username your-windows-login
 # e.g. Xauth username fmoser (not fmoser@unibz.it)
@@ Line 242: / Line 266: @@
   /sbin/ifconfig eth0 mtu 1392
+----
+Allow local (LAN) access when using VPN (MacOS)
+{{:auth:howto:linux:allow-local-lan-access-with-vpn.png?400|VPN preferences}}